Single location installation

The VFD, often called an ac drive or inverter, takes a single- or three-phase signal and varies the speed of a three-phase ac induction motor. This is its main benefit. Running a motor more slowly can save significant energy, and speed changes may be useful to the application. Another big benefit is adjustable acceleration and deceleration. Less acceleration can soften the mechanical forces at motor start and reduce inrush current.

There are both physical and electrical installation basics to be aware of when using a VFD. When mounting the VFD on a back panel, be sure to check the specifications. It is common for multiple devices to be installed in one location, but all VFDs need proper air flow, so check the installation instructions carefully when laying out a control panel.

Mount the drives vertically. Some drives can be mounted with no clearance, but it's common to have a minimum side-to-side spacing of 50 mm or more and to have vertical clearance above and below the drive of mm to mm.

It's not uncommon to hear about noise problems in VFD applications. However, proper shielding and grounding and the use of filters or line reactors can help.

If multiple VFDs are installed in a single location, don't daisy-chain the ground wire; it creates ground loops. Connect each ground to a single ground point, connected in parallel. The line reactor can help to protect from transient voltages and reduce harmonics to or from the drive.

Keeping the load-side—output—wiring less than 75 ft between the drive and motor, or using a load-side reactor, can help to reduce the potential insulated-gate bipolar transistor IGBT reflective wave damage. Opening a contactor at the line or load side of a VFD while the motor is running can cause failures in the inverter section of the drive or reduce its life. Either select the Specify port number check box and type the port number that you want the SharePoint Central Administration web application to use, or leave the Specify port number check box cleared if you want to use the default port number.

On the Completing the SharePoint Products Configuration Wizard page, review your configuration settings to verify that they are correct, and then click Next. On the Configuration Successful page, click Finish. When the wizard closes, setup opens the web browser and connects to Central Administration. If you are prompted for your user name and password, you might have to add the SharePoint Central Administration web site to the list of trusted sites and configure user authentication settings in Internet Explorer.

You might also want to disable the Internet Explorer Enhanced Security settings. If you see a proxy server error message, you might have to configure proxy server settings so that local addresses bypass the proxy server. Instructions for configuring proxy server settings are provided in the following section. For more information about how to configure browser and proxy settings, see Configure browser settings.

If you are not using Internet Explorer, you might have to configure additional settings for your browser. For information about supported browsers, see Plan browser support in SharePoint Servers and To confirm that you have configured browser settings correctly, log on to the server by using an account that has local administrative credentials.

Next, connect to the SharePoint Central Administration web site. If you are prompted for your user name and password when you connect, perform the following procedures:.

To add the SharePoint Central Administration website to the list of trusted sites. On the Security tab, in the Select a zone to view or change security settings area, click Trusted Sites , and then click Sites.

Clear the Require server verification https: for all sites in this zone check box. To configure proxy server settings to bypass the proxy server for local addresses.

In the Automatic configuration area, clear the Automatically detect settings check box. You have now completed setup and the initial configuration of SharePoint Server.

You have created the SharePoint Central Administration web site. You can now configure your farm and sites, and you can select services by using the Farm Configuration Wizard. On the Configure your SharePoint farm page, next to Yes, walk me through the configuration of my farm using this wizard , click Start the Wizard.

On the Service Applications and Services page, in the Service Account section, click the service account option that you want to use to configure your services.

Security note : For security reasons, we recommend that you use a different account from the farm administrator account to configure services in the farm. If you decide to use an existing managed account — that is, an account of which SharePoint Server is aware — make sure that you click that option before you continue.

In the Services section, review the services that you want to use in the farm, and then click Next. In the Title and Description section, in the Title box, type the name of your new site. In the Template Selection section, in the Select a template list, select the template that you want to use for the top-level site in the site collection. To view a template or a description of a template, click any template in the Select a template list. On the Configure your SharePoint farm page, review the summary of the farm configuration, and then click Finish.

After you install and configure SharePoint Server, your browser window opens to the Central Administration web site of your new SharePoint site. Although you can start adding content to the site or customizing the site, we recommend that you first perform the following administrative tasks.

Configure usage and health data collection You can configure usage and health data collection in your server farm. The system writes usage and health data to the logging folder and to the logging database. Configure diagnostic logging You can configure diagnostic logging that might be required after initial installation or upgrade. The default settings are sufficient for most situations. Depending upon the business needs and life-cycle of the farm, you might want to change these settings.

Configure incoming e-mail You can configure incoming e-mail so that SharePoint sites accept and archive incoming e-mail. On the Select file location and product language page, select the File location for the program files. When the installation completes, you see a list of successfully installed system components. Click Close. SQL Server options during custom installation.

Decide which SQL Server and database to use with the below options. SQL Server options:. With support questions and requests, please contact the Milestone Support Community. Please do not include any personal data in your response, such as name, email, phone number etc. Should you provide any personal data, Milestone will process such personal data in accordance with our Privacy Policy. Your personal data will be deleted as soon as possible in accordance with our Privacy Policy.

Upgrade in a cluster. Issue: Recording Server goes offline when switching Management Server cluster node. Multiple management servers clustering explained. Milestone Documentation. This page is not yet available in your language. The installation files unpack. Accept these and the unpacking continues. Select the Language to use during the installation this is not the language that your system uses once installed; this is selected later.

Read the Milestone End-user License Agreement. Select the I accept the terms in the license agreement check box and click Continue. On the Privacy settings page, select whether you want to share usage data, and click Continue.

Select Single computer. On the Assign a system configuration password page, enter a password that protects your system configuration. You will need this password in case of system recovery or when expanding your system, for example when adding clusters.

On the Select file location and product language page, do the following: In the File location field, select the location where you want to install the software.

In Product language , select the language in which to install your XProtect product. Click Install. When the installation completes, a list shows the components that are installed on the computer.

Click Continue to add hardware and users to the system. On the Enter user names and passwords for hardware page, enter the user names and passwords for hardware that you have changed from the manufacturer defaults. Click Continue and wait while the system scans for hardware.

On the Select the hardware to add to the system page, select the hardware that you want to add to the system. Click Continue and wait while the system adds the hardware. On the Configure the devices page, you can give the hardware descriptive names by clicking the edit icon next to the hardware name.